news | blog

10 Minute Concrete Floor Crack Mender & Spall Repair

10 Minute Crack Repair

Ultra Fast Concrete Crack Mender and Spall Repair Resin

Discover the cutting-edge advancements in concrete repair technology. Presenting our lightning-speed, durable, and efficient crack mender and spall repair resin.

Whether it’s reviving floors in bustling warehouses, busy parking facilities, or any structure requiring steadfast and enduring repairs, do it with unprecedented efficiency.

But that’s not all! This multi-purpose resin is also your solution for quick asphalt road fixes.

Want a safe, non-slip finish? Simply integrate our recommended sand aggregate.

Concrete Confidence: Experience Restoration Mastery in Moments!

10 Minute Concrete Floor Crack Mender & Spall Repair

SealBoss 6060 QuickFix

This Structural Polyurethane is an advanced material that addresses the challenges faced in repairing damaged concrete. Its unique characteristics and properties make it an ideal solution for various applications and environments.

The material’s low surface tension and viscosity allow for easy and complete saturation bonding of cracks, requiring only minimal preparation to remove loose debris.

When the material is allowed to gravity-flow to the full depth of the crack, the repair is considered structural.

Manufactured sand or quartz can be introduced into the repair process and added at a ratio of up to two parts sand to one part mixed polyurethane during crack filling to extend the material’s coverage and enhance its strength. SealBoss 6060 is highly versatile and can be applied over a wide range of substrate temperatures, making it suitable for use in frozen and cold storage warehouse applications or cold weather applications. After the repair is completed, the surface is can be ready to accept traffic in as little as ten minutes at 72°F (22°C), ensuring minimal disruption.

SealBoss 6060 QuickFix is Your Fast Concrete Floor and Road Repair System

SealBoss 6060 is a super low viscosity, fast setting two component polyurethane concrete crack mender offering outstanding penetration properties, superior strength and durability.

At a mixing ratio of 1 to 1 by volume, the mixed product can be used neat or mixed with a sand aggregate to create a quick repair mortar. The product is cured chemically and does not need any moisture to react.

10 Minute Concrete Floor Crack Mender & Spall Repair

Very Fast Cure
Short Turnaround Time
Very Low Viscosity
Creates Repair Mortar with Dried / Silica Sand
Super Strong Polyurethane Formula
Outstanding Bond Strength & Penetration Properties
Use In Combination With SealBoss 6500 Polyurea Joint Fillers
Products is available in Cartridges

6060 QuickFix Resin is a very thin chemical cure product. 6060 polyurethane crack mender resin reacts within minutes of application. You can use it as low viscosity self leveling resin or as a quick set repair mortar. The product has excellent bond strength, compressive & tensile strength, all of which are achieved within minutes of cure. SealBoss 6060 QuickFix and fast cure SealBoss 6500 Polyurea Joint Fill products are the recommended choice for timely floor repairs in commercial warehouses and other areas of traffic. Products are also available in cartridges

Chris Coderre

Regional Sales Manager

In Conclusion

The ability of SealBoss 6060 to penetrate deeply into cracks and bond directly to the concrete-aggregate matrix ensures long-lasting and reliable repair.

Structural Polyurethane is adaptable for use in extreme temperature conditions, making it suitable for a range of industries and applications where traditional repair materials might fail.

The rapid curing time of SB 6060 minimizes downtime and disruptions, allowing for swift resumption of normal activities in the repaired area.

Given the material’s versatile nature, it can be used to address a wide variety of concrete damage, including cracks, spalls, and other structural defects.

The compatibility of SealBoss 6060 with Portland Cement Concrete (PCC) enables a smooth blending with pre-existing concrete structures, minimizing the aesthetic effects of repairs.

By incorporating SealBoss 6060 Structural Polyurethane into the repair process, professionals can effectively extend the service life of concrete structures while maintaining their appearance and structural integrity. This innovative material offers a highly effective, efficient, and durable solution for restoring distressed concrete and ensuring its longevity.

10 Minute Concrete Floor Crack Mender & Spall Repair Related Articles

Learn More

Feel free to reach out to us at 714-662-4445 for any inquiries, or submit a contact request here. We are eager to assist you in finding the right solution. Expert technical representatives are available to provide on-site support upon request.

Floor & Road Mender Products

Click Here

crack mender

Contact Your SealBoss ® Technician

Concrete Repair Cartridge Solutions

Professional Cartridge Systems

SealBoss Cartridge System Solutions

SealBoss Provides Professional-Grade Solutions in 22 oz. Dual Cartridges as a Convenient Alternative to Bulk Products, Elaborate Equipment and Machinery

Concrete repair cartridges are tailored for smaller repair tasks where only a limited amount of product is required. They are especially useful for areas that are hard to reach with larger equipment. Additionally, for floor repair tasks, these cartridges are ideal for last-minute adjustments and minor touch-ups.

Cartridge Product Range

Water Stop & Leak Sealing Application HOT SHOTS
1500 Hydro Active PUR and 1640 Structural Void Fill Foams
Joint Fill & Floor/Road Repairs
6500 Polyure Joint Filler and 6060 Spall / Concrete Crack Mender
Epoxy – Structural Repairs
Crack Injection Epoxy Resins & Epoxy Paste Adhesives

How to Use Cartridges – Checklist

For best results we recommend that you to follow a few simple guidelines and cartridge/product conditioning techniques prior to application.

Condition cartridges to room temperature in colder climates or extreme heat
Shake cartridges with liquid content sufficiently prior to use
Only use static mixer recommended for product
Only use clean static mixers
Push out any air by moving product through the static mixer while holding cartridge in an upright position
Dispense and discard a small amount of product into a dedicated vessel to allow for an even mix
Your cartridge is now primed and ready to go
Dispense evenly
Remove static mixer and replace with cap for any storage

Inquire more about SealBoss Concrete Repair Cartridge Solutions when you call us here at SealBoss. Your representative will be happy to help you out.

Find detailed information and media links on the SealBoss Cartridge Overview Page

SealBoss CARTRIDGE SYSTEM

Click Here

CARTRIDGES

Contact Your SealBoss ® Technician

SealBoss Product and Application Training

Product & Application Training

Knowledge Is Power

Our Technical Sales Managers

Passionately Sharing
Experience
and Knowledge
with Industry Professionals
Everywhere

We bring the

Classroom to You

We take pride in educating engineers, distributors and contractors worldwide in the use of our products and equipment. If you like more information on the classroom services, on-the-job training, and lunch and learns we provide, please contact our technical sales staff at 714-662-4445

Contact us for Your Training

Click Here

TRAINING

Hands-On Demonstrations

Hybridized Training

There is a lot of benefit to conducting the training in two phases, first with the classroom setting, and then following that up with the actual Hands-On Demonstrations to bring all of the principles of applications and installation to the forefront physically to drive home the ideas covered in the classroom.

Twelve Day SealBoss Training Tour Down Under

The SealBoss hybrid training tour kicked off at Bayset in Brisbane with subsequent training session visits to the branches in Townsville, Melbourne, Canberra (ACT), Ingleburn and eventually ended in Seven Hills in New South Wales.

Chris Coderre, National Sales Manager at SealBoss, journeyed over 7,000 miles to Australia to collaborate with Bayset, our esteemed stocking distributor. This trip marked a significant milestone as we celebrated the opening of three Bayset branches, enhancing our local presence.

Each branch hosted a full-day, dynamic training session, blending practical demonstrations with theoretical learning to enrich both contractors and Bayset staff. Chris Coderre, who is nearing a decade with SealBoss, emphasized the importance of delivering substantial value through these sessions.

“Traveling such a great distance obligates us to provide a comprehensive experience. If we didn’t achieve that, there would be little point in making the journey at all,” Coderre explained.

Attendees at each location were particularly enthusiastic about the live demonstrations, which covered cold joint, crack injection, and consolidation grouting. Even those accustomed to traditional classroom settings found the hands-on approach both refreshing and informative. “Integrating practical demonstrations with theoretical training underscores our commitment to teaching correct water stop injection techniques to both installers and engineers,” Coderre added.

We extend our heartfelt gratitude to the Bayset team for their exceptional efforts in organizing and hosting the training sessions. Their hard work ensures that every participant leaves more knowledgeable and skilled.

Stay tuned for more updates as we continue to grow and innovate across Australia!

Contact us for Your Training

Click Here

TRAINING

Concrete Repair Training

Overview

Partnerships and Free Training: The Key to Success in Today’s Market
The Benefits of Manufacturer-Distributor Partnerships for Product Quality and Customer Training
60 Contractors Attend Free Concrete Repair Training at Local Distributor
Join Free Local Concrete Repair Training Sessions

Partnerships and Free Training

The Key to Success

In the competitive world of construction and repair, strategic partnerships and continuous training are essential for success. Manufacturers and distributors, by joining forces, can efficiently provide high-quality products and offer comprehensive training, allowing them to thrive in the current fast-paced market.

One way to foster these cooperative relationships is through local customer training sessions, where manufacturers, distributors, and contractors have the opportunity to learn, grow, discuss and share their knowledge and expertise. This collaboration enables all parties to better understand each other’s needs, and ultimately leads to improved product quality and customer satisfaction.

The Benefits of Manufacturer-Distributor Partnerships for Product Quality and Customer Training

Manufacturer-distributor partnerships bring several advantages to the table. For manufacturers, they help extend market reach, improve operational efficiency, and gain valuable insights that can be used to enhance product offerings. Distributors, on the other hand, can rely on a wide range of top-quality products and offer localized training sessions that enable their customers to stay up-to-date with the latest advancements in the industry.

In turn, the end-users, such as contractors, benefit from these collaborations, as they have access to cutting-edge products and resources that can enhance their skills and expand their knowledge. This ultimately leads to higher levels of customer satisfaction, as their own clients can appreciate the superior quality of work and adherence to industry standards.

60 Contractors Attend Free Concrete Repair Training

A perfect example of such collaboration is the recent SealBoss Corp. Concrete Repair Training session hosted by Cascade Aqua-Tech. The event proved to be a great success, attracting over sixty contractors eager to learn more about concrete repair systems and their proper applications.

True to the SealBoss training tradition, this informative and hands-on session was provided free of charge to all contractors attending. During the seminar, participants learned the basic principles of polyurethane crack injection, leak sealing, and permeation grouting. They became familiar with the comprehensive system solutions offered by SealBoss product families, consisting of various structural epoxy systems and industrial floor repair techniques.

Chris Coderre, Regional Sales Manager, highlighted the significance of such events: “The true synergy from not only a business standpoint but from an educational standpoint to better the techniques and methods used in our industry is whole and fortified when you can combine the technical expertise of the material manufacturer, the contracting community, and most importantly the distribution network available locally to that contracting community and have everybody under one roof.”

By offering hands-on demonstrations, these training sessions effectively bridge the gap between theoretical knowledge and practical application. As Coderre observed, witnessing the transformation of complex concepts into tangible actions within a short time frame can significantly dissolve any skepticism and clarify doubts regarding industry practices.

Such training sessions also embody the age-old saying, “Give a man a fish, and you feed him for a day. Teach a man to fish, and you feed him for a lifetime.” By providing contractors with the education and resources necessary to improve their own trade, manufacturers and distributors empower them to better serve their customers, making a lasting positive impact on the industry as a whole.

Join Free Local Concrete Repair Training Sessions

If you are seeking hands-on concrete repair training for your customer base, look for manufacturer-distributor partnerships that offer accessible and comprehensive training sessions designed to enhance your skills and knowledge.

These collaborative training opportunities are an excellent way for contractors to stay abreast of the latest industry trends, learn new techniques, and refine their skills, ultimately leading to better results for their clients and higher levels of customer satisfaction.

In conclusion, manufacturer-distributor partnerships not only result in a broader range of high-quality products and local training opportunities but also serve to foster a sense of community and shared knowledge among contractors within the industry. By engaging in these collaborations, manufacturers, distributors, and contractors can better understand the needs and preferences of their customers, creating a thriving and prosperous industry for all.

Another great training day of joint effort Cascade Aqua-Tech Ltd. & SealBoss Corp. Concrete Solutions

This recent training on SealBoss water stop crack injection, leak sealing & permeation grouting was very timely as many water-proofing contractors are dealing with leaking cracks during this time of the year.

The primary focus was on SealBoss 1510 & 1570-hydrophobic polyurethane water cut-off and leak-seal injection foams and the P2002 pump system. In addition, we also provided education on epoxy injection for structural repairs and joint filler for floor crack repairs.

Christopher Coderre, thank you for going above and beyond to make this day a huge success. We are so grateful for your continued support.

Rosiro Lowe,
Sales And Marketing Specialist at Cascade Aqua-Tech Ltd.

Contact us for Your Training

Click Here

TRAINING

Leaking Crack Repair

Coached by a Top Industry Professional

In the world of construction and maintenance, “leaking crack repair” is a term that frequently emerges, particularly when addressing structures that contain water or are vulnerable to moisture and water intrusion. Addressing these cracks swiftly and efficiently is vital for the structure’s safety and durability.

Sealing the Future – Preserving the Past
Since 1988

Leaking Crack Repair

Sealing the Future – Preserving the Past
Since 1988

The Need for Crack Injection Training

A prominent general contractor, who usually subcontracts such tasks, expressed the need for immediate crack injection training on a specific jobsite. Their primary aim was to acquire the expertise for smaller projects, allowing them to handle leaking crack repair internally on certain timely projects. This proactive approach not only saves time but also ensures that minor issues can be addressed before they escalate.

A Case Study: Water Treatment Tank Crack Sealed

Scope: New Concrete Tank – Water Test Failure – Asses and Seal

The facilities in question comprised three holding cells, separated by two poured-in-place division walls. During a leak test on the outer two tanks, visible cracks were detected. These cracks, deemed non-structural for repair purposes, showed signs of dampness and minor leaks, emphasizing the need for immediate leaking crack repair. Pressure crack injection with a hydrophobic polyurethane expanding water stop foam utilizing an electric injection pump and mechanical injection packers was specified as the method of restoration.

The Repair Process

Materials Used: SealBoss 1570, SealBoss 15x
Additional Tools: SealBoss 13-60S packers, SealBoss 495 Injection Pump, Hammer Drill w/ 12” x ½” bit, PPE

For training purposes, a weeping crack was chosen for repair. This crack, though narrow, spanned about 10 feet in height and meandered across the wall. Given that the newly constructed wall was 14 inches thick, the repair strategy involved guiding the team to drill 5 to 7 inches out from the crack. The drilling was done at a 45-degree angle, aiming back towards the crack, employing the crack stitch method.

Depth of Intersection: The further the drill hole is from the crack, the deeper it will intersect the crack within the structure. This results in a more profound point of injection.

Considerations for Thicker Structures: A deeper injection point is often preferred in thicker structures. However, the length and reach of the drill bit play a crucial role in determining the optimal distance for the drill hole.

Avoiding Dead-End Drill Holes: A drill hole that misses the crack won’t facilitate the injection of the chemical grout into the structure. Such holes are termed “dead-end drill holes” and are ineffective for the purpose of grout injection.

In summary, while determining the spacing of drill holes, it is vital to balance the desired depth of injection with the capabilities of your drilling equipment to ensure effective grout injection.

To ensure precision, the placement was set parallel to the fissure. A 0.5-inch masonry bit, attached to a hammer drill, was used for the drilling process. Once the clean, crack-intersecting holes were established, SealBoss 13-60S heavy duty steel injection packers were installed.

The repair commenced from the bottom, progressing upwards. The SealBoss 495 injection pump, paired with the SealBoss 1570 NSF/ANSI/CAN 61 drinking water contact certified chemical grout, was used for the leaking crack repair. As the repair proceeded, water and material were observed exiting the substrate. This was a positive sign, indicating effective penetration and successful stopping of the water penetration and sealing of the crack.

Final Thoughts

Leaking crack repair is an essential aspect of maintaining the structural integrity of buildings and facilities. With the right knowledge, tools, and materials, such as those provided by SealBoss Corp., even the most challenging cracks can be effectively addressed. Whether you’re a contractor looking to expand your skill set or a facility manager aiming to maintain your structures, understanding the nuances of leaking crack repair is invaluable. Our SealBoss Water Stop Specialists are always ready to assist you.

Related Links

Contact Your SealBoss ® Technician

Tunnel Water Stop Injection Leak Repair

Tunnel
Water Stop
Injection
Leak Repair

Leak Sealing
Systems

Tunnel Water Stop Injection Leak Repair with Polymer Grout Injection

Introduction:

Tackling water leakage in tunnels, this piece outlines the challenges and solutions associated with different tunnel types, such as utility, vehicle, subway, rail, and pedestrian tunnels. It proposes the use of Polymer Injection Grouts, specifically acrylate gels and polyurethane resins, for effective leakage sealing and structural consolidation.

The article discusses the properties and applications of acrylate gels, guiding through the steps of leak repair including diagnosis and material selection. Additionally, it highlights SealBoss’s products tailored for addressing underground water ingress and emphasizes the importance of proper training and equipment for repair personnel.

Tunnels, serving diverse purposes and varying in structure, are crucial infrastructures. Below is an overview of the tunnel types most susceptible to water leakage and the associated risks:

Utility Tunnels: Hosting vital systems like electrical wires, water pipes, and gas lines, water leaks in these tunnels can cause pipe corrosion and electrical faults, endangering safety and disrupting services.

Vehicle Tunnels: Susceptible to water leakage from tunnel walls and the road, accumulated water can create dangerous driving conditions, resulting in accidents and traffic congestion.

Subway Tunnels: Positioned beneath city areas, they are at risk of water leaks from surrounding soil and existing utilities, leading to service disruptions, delays, and increased maintenance costs.

Rail Tunnels: Highly sensitive to water intrusion due to their electrical systems and the high-speed trains, water leakage can damage the track bed, potentially causing uneven rails and, in severe cases, derailments.

Pedestrian Tunnels: Vulnerable to water leaks, they can become slippery, posing fall risks, and the dampness can foster mold and bacteria growth.

How to stop leaks of high hydrostatic pressures with Injection Grouts

Water ingress can cause immediate damages as well as lead to increased project costs and may lead to many other issues down the line.

Water leaks through cracks, joints and voids can be repaired with cost effective and highly successful injection systems, utilizing chemical grouts such as multi component acrylate gels and single component polyurethane resins.

Appropriately engineered resin injection systems do not not only seal leaks in the structure itself, but can transform loose sands behind the structure to a confined consistency similar to sandstone, and consolidate gravel to a bonded conglomerate.

Example: SealBoss Acrylates Used to Seal Leaks in Tunnel

What are Acrylate Gels?

Acrylate Gels, also known as Acrylic Gels, are very flexible, super low viscosity — similar to water — hydrophilic gels designed for non-structural injections of cracks, joints, voids, and used for grid, curtain, bladder injection and as sealant in the injection tube system.

Due to their extremely low viscosity and low surface tension, polyacrylate gels offer superior penetration properties. Acrylates are gel time adjustable to meet jobsite conditions such as temperature and injection distance.

Acrylic gels are used to waterproof leaks and create a compression seal due to their hydrophilic swelling behavior when in contact with water.

Acrylate injection equipment can easily be cleaned with water.

SealBoss provides a wide range of products to control water ingress into underground mining works, tunnels and many other commercial structures with leakage issues. We supply materials for waterproofing, consolidation, sealing, crack and joint repair, bonding and cavity filling.

Tunnel Water Stop Injection Leak Repair

How to Start Acrylate Injection Leak Sealing Injection Repairs

The principal steps to solve a problem are:

Diagnosis of the problem
Specification of injection methods
The correct choice of resin, pumps, packers and accessories
Training of installation personnel, a well trained and experienced team is paramount

Will I need more than One Product?

That depends on the conditions of the jobsite. Polyurethane and Acrylate injection systems offer a variety of solutions to problems found in geotechnical applications, in tunneling, waterproofing underground works and civil engineering in general. While there is no single resin that will suit all conditions, the correct resin must be used to achieve the best results possible and to meet the requirements of the specification.

If there are any questions about the various chemical grouts available, please do not hesitate to contact us, we are here to assist in any way we can. Always remember to work safely by wearing eye protection and gloves when handling any type of chemical systems.

Which products are shown in the videos?

Products used for Tunnel Water Stop & Leak Sealing Injection

Related Article

Flooded Tunnel Repair

Call Your SealBoss Technician

If you have any questions on crack injection water stop procedures or any injection related applications, please contact our team of qualified SealBoss representatives to schedule an on site consultation & full injection systems training. Call us at 714-662-4445.

SealBoss Leak Sealing Systems

Click Here

Injection

Contact Your SealBoss ® Technician

Waterproofing Parking Structure Cracks

Waterproofing
Parking Structure Cracks

Acrylic
Gel
Injection

WATER

On Earth life cannot exist without it and at the very same time water can take life away. This principle resonates for the industry of construction as well. More specifically, this idea is a direct parallel to concrete and its make up.

Without water, concrete cannot chemically transform and become the fluid, placeable and pourable material that it is. However, once cured, nuisance water within concrete structures can internally destroy its structural integrity by corroding reinforcing steel, eventually rendering the concrete structure useless. Water, in sum, is perhaps one of the most simple and essential yet potentially destructive forces on our planet.

Waterproofing Parking Structure Cracks

At a parking structure in Burlingame, California, the shotcrete structure and mat slab were exhibiting signs of unwanted ingress from the water table outside of the building.

While evidence of cracking was not necessarily present, efflorescence on the interior surface of the walls told the tale that the migration of unwanted groundwater was presenting a problem.

The structure is referred to as an Automated Parking Structure where building tenants can retrieve their automobiles by entering a code at the entry point to the structure and have their vehicles essentially “delivered” to them once the internal workings of the structure retrieve the vehicle. It becomes obvious from this description of the project that water has no place in the intricate electronic systems that comprise this facility but more so on or near the vehicles that live in this structure. Something needed to be done and a certified specialized contractor was called in to get the water mitigation handled.

The construction of the concrete is something to note, particularly with respect to the steel in place at a double mat (2 layers within the walls) of #9 and #11 bars at a spacing of 24” on center each way. This reinforcing steel is a sturdy configuration –and a lot of steel — all of which is susceptible to corrosion if water is present after the shotcrete’s cure out.

That amount of steel, if subject to corrosion, could, over time lead to spalling and eventually an overall degradation of the structure if left unaddressed.

Something Needed To Be Done

The SealBoss 2400 super low viscosity acrylic gel injection system was the answer for waterproofing parking cracks permanently.

The 2400 system is extremely well suited to seal structures with very fine and hairline cracks and fissures.

The 24’ high walls needing injection stood atop a 6’ thick cast-in-place mat slab and were +/- 24” thick. Extending from the tops of the walls to grade were 4’ high cast-in-place ring beams. By drilling into the walls 22” (not all the way thorough) and setting mechanical packers into the drilled holes, the delivery of the SealBoss 2400 system was now possible to as was its migration within the substrate.

The environmentally friendly SealBoss 2400 offered outstanding penetration properties similar to plain water, allowing it to permeate throughout the wall’s network of fissures, no matter how tight and narrow. In some instances, the material would shoot out of pinholes and cracks barely visible to the naked eye several feet away, further showcasing its ability to navigate the concrete’s crack and pore network thoroughly and effectively. Once gelled, the material prevented unwanted water migration to reinforcing steel within the substrate.

Mission accomplished

If there are any questions about this project in need of answering please do not hesitate to contact us, we are here to assist in any way we can. Always remember to work safely by wearing eye protection and gloves when handling any type of chemicals. We hope you enjoyed our review of the project outlined above and encourage you to explore our website to learn more about our vast array of waterproofing solutions for concrete structures.

Video – Acrylate Gel Injection SealBoss2400
Super Low Viscosity Penetration Properties

– See How SealBoss 2400 Pushes through
Finest Cracks and Fissures
– See Port to Port Injection Technique
– See Product Travel of Several Feet

SealBoss 2400 Gel Injection System

Links to Leak Sealing with SealBoss Acrylate/Acrylic Super Low Injection System

SealBoss Acrylate/Acrylic System

Click Here

Acrylate

Contact Your SealBoss ® Technician

Acrylate Resins

Acrylic Polymer Injection

Introduction

Discover the benefits of Acrylate Resins in construction and repair work, known for their water affinity, flexibility, and ultra-low viscosity.

This article introduces the unique properties that make Acrylate Resins, especially SealBoss 2400, a top choice for sealing and repairing concrete structures efficiently and effectively. Explore how these resins can transform your water-related projects.

Acrylate Resins Explained

Acrylate Resins are a popular choice in construction and repair work, and here is why:

Hydrophilic Nature: Acrylate Resins love water, making them excellent at sealing and waterproofing.
Flexibility: Acrylate Gels are super flexible, perfect for non-structural injection into cracks, gaps, and other spaces. Whether it’s crack injection, injection hoses, compartment setups, or large area injections, such as grid or curtain injection, acrylate resins have got you covered.
Super Low Viscosity: Think of Acrylate Gels as having a water-like consistency during application. This means they can flow into and fill tiny spaces with ease, ensuring optimal penetration.
Adjustable Gel Time: Depending on the site’s conditions, like temperature and how far the resin needs to be injected, you can adjust how fast or slow the Acrylate Resins hardens.
Sealing Power: When Acrylate Resins come in contact with water, they swell. This hydrophilic swelling behavior ensures a tight, leak-proof seal.
Easy Cleanup: Spills or excess? No problem. The injection equipment and any uncured messes can be easily washed away with water.

In short, if you’re looking to seal or repair water bearing concrete structures, Acrylate Resins might just be your best bet!

SealBoss 2400 Acrylate Gel Resin

SealBoss 2400 is the super flexible and ultra-low viscosity injection alternative in the world of Water Stop and Leak Sealing:

Super Flexible & Ultra-Low Viscosity: This combination ensures an exceptional flow, enabling the resin to penetrate even the finest cracks and joints effortlessly. The added flexibility is crucial as it allows the resin to adapt and move with the natural expansion and contraction of materials, reducing the risk of future leaks or damage.
Hydrophilic Acrylic Formulation: SealBoss 2400 is designed to produce a robust yet flexible gel gasket, making it ideal for handling expansion joints.
Versatility: Whether it is for a primary injection, a secondary pass to tighten up, or for injection tubes, SealBoss 2400 is your go-to solution.
High Performance: SealBoss 2400 offers resilience and top-notch quality suitable for demanding applications.
Eco-Friendly: SealBoss 2400 is water-based, making it a greener choice for the environment.

With SealBoss 2400, you’re choosing efficiency, ultra low viscosity, user friendliness, and excellence all in one package!

Related Articles

Contact Your SealBoss ® Technician

Button Head Packers | Hammer In Packers | Bang In Ports

SealBoss Plastic Specialty Injectors

Plastic Buttonhead Packers | Plastic Hammer-In Ports

Exploring the Versatility of Grout Injection Packers

Grout Injection Packers, also commonly referred to as Packers, Ports, or Injectors, serve as essential tools in the field of construction and repair, particularly in the context of crack injection and leak sealing.

To clarify their various applications and types, these packers are often accompanied by descriptors such as Grout, Epoxy, Mechanical, and Surface, leading to specific terms like Mechanical Packers, Epoxy Injectors, and Surface Ports.

The lexicon of packer terminology extends even further as injection professionals devise elaborate combinations of terms to precisely describe their equipment. For example, phrases like Mechanical Injection Packers, Plastic Grout Injection Ports, and Epoxy Crack Injection Plastic Surface Nozzle Ports with Perforated Tri Base Design and Extra Long Anti Leak Plastic Caps, though complex, provide insiders with valuable specificity about the tool’s design and functionality.

In our video below, we demonstrate the particulars of the Plastic Button Head Packer, a tool also recognized in the industry under names such as Progressive Screw Injector, Port, Packer, Top Hat Packers, or Easy Slide Packers. These names reflect the packer’s unique features, such as its compatibility with button head or slide couplers.

Furthermore, we introduce the Hammer-In Packer, an alternative known variously as Hammer-In Port, Bang In Packer, or Hammer Blow Injector. This variation emphasizes the packer’s method of installation, which involves a simple, forceful action to position the packer into place.

SealBoss® stands at the forefront of this industry as a premier international supplier of both packers and surface ports. Our extensive selection includes surface-mounted epoxy injection ports compatible with all SealBoss epoxy injection systems. Whether you’re working with handheld manual gun injection, pneumatic gun injection, epoxy pump injection, cartridge injection, or high pressure zerk coupler connected epoxy injection, our products are designed to meet your project’s specific needs.

By offering this array of sophisticated and versatile tools, SealBoss® caters to the diverse demands of the construction and repair industry, ensuring that professionals are equipped with the right packers and ports for every situation.

SealBoss Specialty Plastic Ports Our Button Head Plastic Port has a large inner diameter and a large anti return valve in the shaft which permits high volume material flow. This packer is extremely well suited for Curtain Injection and Slab Lifting applications where volume product flow is priority and injection pressures are typically lower.

The Hammer-In Port is an economic alternative to Mechanical Packers. The port is placed quickly and tightening is not necessary. This is a fast placement - low cost injection port that many contractors utilize.

Please don't hesitate to contact us here at Sealboss for more information about our extensive packer selection. Your representative will be happy to assist.

We provide on-site support and training all SealBoss System Solutions.

Technical Sales Team